+49 7025 / 92 19 0|info@maurer-ir.de
Electronic process units
Electronic process units - Image 2

Electronic process units

Complement your MAURER pyrometer with an electronic process unit and benefit from numerous functions. With this device you have all relevant data immediately in view. Adjusting the settings can be easily done thanks to the intuitive handling of the menu navigation. In addition, it enables you to record measured data and set the parameters for your pyrometer effortlessly and without a computer. For further control purposes, a large amount of data and signals can be tapped or fed from an external source via the terminal block on the rear side. Depending on the model, additional features are available for you. Please see the table below:

Category:

Description

Features and characteristics of all models

AED 1012, AED 1012-C and AED 1012-PC:

    • Display unit: gives an overview of all important information
    • Overall parameter setting of pyrometer without computer possible
    • 2 seperately adjustable switch outputs with optorelais
    • Works as voltage supply for the pyrometer
    • Digital pyrometer interface RS232 or RS485
    • Authorization management with optional PIN protection against unauthorized access
    • Automatic determination of emissivity and transmission
    • Data logging to USB flash drive with real time clock
    • Ultra fast sampling rate of 50 µsec
    • Multilingual Touchpanel
    • 6-digit temperature display °C / °F

Additional features and characteristics of the AED 1012-C

    • PID Controller with set-point value setting (manually – external)
    • Autotuning feature for automatic determination of PI-parameters

Additional features and characteristics of the AED 1012-PC

    • PID Controller: define up to 500 programs with 1023 program steps in total
    • Autotuning feature for automatic determination of PI-parameters
    • 2 additional separately adjustable switch outputs with optorelais (4 in total)

 

Technical Data

AED 1012 AED 1012-C AED 1012-PC
Datasheet
Pyrometer interface RS232 / RS485, switchable
Computer Interface USB 2.0
Optional: ProfiBUS, ProfiNET, Ethernet, Ethercat
Data recording
Recording on USB flash drive or PC, with real time clock
Input of actual value
Current loop of pyrometer (0 – 20 mA or 4 – 20 mA / input impendance 20 R)
Measurement indication
6-digit programmable, adjustable display rate 100 ms – 10 s
Sampling time 50 µsec 100 µsec 100 µsec
PID parameters — xp: 1 – 1000 %      ti: 0,1 – 9999 ms     td: 0,1 – 9999ms      P: 0 – 100 %
Program count / -steps — — 500 programs
1023 steps in total
Program step length 1 ms to 3600 ms
Measuring range Manual scaling for analogue pyrometers from -50 °C to 4000 °C
Automatic scaling for digital pyrometers
Switching output Set points adjustable within measuring range
2 x optorelais (optional 4 x) with changeover contacts, each 60 VAC / 100 mA 4 x Optorelais,  je 60 VAC / 100 mA
1 x optorelais pyrometer limit
Switching hysteresis: Adjustable between 0 – 50 °C, Response time 3 ms
Operating / Storage temperature 0 – 60 °C   /   -10 °C – 70 °C
Supply voltage 80 – 305 VAC
Power consumption Max. 20 W
Power supply for pyrometer + 24 V / 300 mA (D-SUB)
Signal outputs via 16-pol. screw terminal block
IP Code IP50
Weight / dimensions (LxHxW) Standard:           1,3 kg  /  155,5 x 69 x 204 mm (height with foots: 104 mm)
DIN-version:       1,1 kg  /  96 x 96 x 170 mm (width with power supply connector: 235mm)
panel cutout:       92 x 92 mm

 

stp-Files

Download stp File AED 1012
Download stp File AED 1012 Profibus

Configuration & Assemblies

Configuration Options Equipment
Computer interface: ProfiBUS, ProfiNET, Ethernet, EtherCAT Connection cables
In DIN-housing according to DIN 43700 for panel
 Mounting brackets for panel installation
Connection of second pyrometer via RS232 interface Table top stand
 Additional current output 0 (4) – 20 mA Protection casing IP65
Connection of up to 6 pyrometers via RS485 interface Connection bar for up to 6 pyrometers (AED-6K)
 Two additional switching outputs
Go to Top